Showing posts with label regulator. Show all posts
Showing posts with label regulator. Show all posts

Saturday, November 8, 2014

Increasing 78xx Voltage Regulator Current

Shown in the figure is an IC voltage regulator (also known as stabilizer), designed to increase its current output with the use of an outboard pass transistor. Voltage regulators are designed to produce positive inputs, such as 78xx series, and negative inputs, such as 79xx series. Using this circuit will help increase the current output from a 78xx series regulator. Alternatively, 79xx series can also be used with an NPN type of transistor.





Using a power transistor enables additional current to be loaded while sustaining a steady voltage. But keeping in mind for the limit of input voltage as it should be a few volts above the output voltage. Regulators like 7812, having a 12V output can be set to produce 20V output.  Some 78xx series can surpass up to 36 volts input. Having a high power difference could lead to an overheat and would require sufficient heat sink. Without the heat sink, the transistor might collapse. Lower input could also cause failure due to the decrease in temperature. Power dissipation can be computed as the product of the voltage and the current  P = V * I.
Source:www.zen22142.zen.co.uk
Read More..

Thursday, September 4, 2014

Regulator Power Supply 1A Circuit Schematic


Regulator Power Supply 1A Circuit Schematic

Small power supply that provides a regulated voltage, adjustable between 1.5 and 35 volts at 1 ampere. This schema is ready to use, you just need to add a suitable transformer. This schema is thermal overload protected because the current limiter and thermal overload protection are included in the IC.

This is the Regulator Power Supply 1A Part List :

IC = LM317
P1 = 4.7K
R1 = 120R
C1 = 100nF - 63V
C2 = 1uF - 35V
C3 = 10uF - 35V
C4 = 2200uF - 35V
D1-D4 = 1N4007
Read More..

Tuesday, September 2, 2014

Low Dropout Adjustable Regulator Circuit


Low Dropout Adjustable Regulator Circuit

We frequently acquire requests for voltage regulators for systems for which the accepted LM317 is not suitable. Although the LM317 can acquire ascribe voltages up to 3-40 Volts, and achievement adapted voltages from 1.2-37 Volts, it can alone achievement a reliable anchored voltage if the ascribe voltage is at atomic 2-3 Volts college than the called achievement voltage - e.g. to get a reliable 12.0V output, the ascribe voltage would charge to be 15V+. This voltage aberration is the dropout, the bulk of voltage alone (dissipated/wasted as heat) in the regulator.

Low Dropout Anchored Voltage Regulators

Where a anchored voltage regulator is required, article like the LM2940 ambit can be used. These are low dropout voltage regulators about accessible with anchored achievement voltages of 5, 10, 12, and 15 Volts.

Such a regulator is complete for use for archetype area 12V rated LED spotlights are to be powered with a 12V battery. The array voltage can ambit from 12.5 to 14+ Volts, and we charge a anchored 12.0V to ability the LEDs, so although an LM317 would not be reliable, the LM2940 (which will bead no added than 0.5 Volts) would accord a anchored 12.0V achievement beyond the abounding voltage ambit of the array reliably.

Unfortunatately we cannot use an LM2940 area a non-standard voltage - e.g. 8.50 Volts - is required. Ideally we appetite article with the adaptability of the LM317, but the low dropout characteristics of the LM2950. Fortunately such a basic exists and it is the LM2941 adjustable low bead out voltage regulator (which is pictured above).

The LM2941 can achievement voltages from 5.0 to 15.0 Volts * with a archetypal dropout voltage of aloof 0.5 Volts (@ 1 Amp, beneath for lower currents), and an complete best dropout of 1.0 Volts beyond the abounding temperature range. The LM2941 can accumulation up to 1 Amp of current.

* Note that the best ascribe voltage is 26 Volts, so this basic is not acceptable for 24 Volt rated systems.

Pictured aloft is the archetypal appliance ambit application the LM2941 as an adjustable voltage regulator. The advertence voltage (measured beyond ADJ and GND) is 1.275V. With the resistor R1 about set to 1K, the amount of R2 for any accustomed adapted achievement voltage is affected application the afterward equation:

R2 = R1 (( Vout / Vref) - 1 ))

For example, if an 8.00V low voltage bead out regulator is required, R1 = 1K, Vref = 1.275, and so R2 = 1000((8.00/1.275) - 1) = 5276 Ohms.

Turning the blueprint about we can additionally account the achievement voltage for any accustomed ethics of R1 and R2:

Vout = Vref * ((R1 + R2) / R1)

...so if we accumulate R1 as 1K and set R1 as 5K1 (since the 5276 Ohm amount affected is acutely not a accepted resistor) we see that Vout = 1.275 ((1000 + 5100) / 1000) = 7.78 Volts. (Note that it is accessible to affix accepted resistors in alternation abacus up their ethics to get an exact amount if a actual authentic voltage regulator is appropriate - e.g. 4K7 + 560R + 10R + 5R6 = 5276 Ohms for an 8.00V regulator)

Click actuality to appearance the LM2941 Datasheet (PDF) with sample diagram, and abundant blueprint data.
Read More..

Saturday, August 23, 2014

9 Volt 2 Amp PSU Single IC Regulator Power Supply



Notes

There is little to be said about this schema. All the assignment is done by the regulator. The 78S09 can bear up to 2 amps connected achievement whilst advancement a low babble and actual able-bodied adapted supply.

The ambit will assignment after the added components, but for about-face polarity aegis a 1N5400 diode is provided at the input, added cutting actuality provided by C1. The achievement date includes C2 for added filtering, if powering a argumentation ambit than a 100nF capacitor is additionally adorable to abolish any aerial abundance switching noise.

via : http://www.zen22142.zen.co.uk/Circuits/Power/9v2a.htm
Read More..

Sunday, August 17, 2014

Simple Fixed Current Regulator Wiring diagram Schematic

This Simple Fixed-Current Regulator Circuit Diagram 1-mA current source delivers a fixed current to a load connected between Ql`s collector and ground; the load can be anywhere in the range from 0 to 14 . The schema is powered from a regulated 15-V supply, and the R1/R2 voltage divider applies a 14-V reference to R3. 

The op amp`s output automatically adjusts to provide an identical voltage at the junction of R4 and R5. That produces 1 V across R5, resulting in an R5 current of 1 mA. Because that current is derived from Ql`s emitter, and the emitter and collector currents of a transistor are almost identical, the schema provides a fixed-current source. The output current can be doubled by halving the value of R5.

Fixed-Current Regulator Circuit Diagram

Simple

Read More..